PHILADELPHIA, PA 19144
New Appliance, Heating & A\C Parts & Electric
Motors
We
have most parts for residential and commercial gas ovens, furnaces, boilers,
air conditioners (except some window types), as well as a huge assortment of
electric motors, pumps, blower components, and fan blades for the same. We have most of the popular OEM and generic
replacement parts used on Carrier, Bryant, Trane, Lennox,, York, Rheem-Ruud,
Goodman-Janitrol, Coleman-Evcon-Air Pro, Heil, Nordyne-Miller, Hydrotherm,
Arco-Aire, Amana, Caloric, Fridgidare, Whirlpool, Roper, WCI, G.E and many
others.. We’re also an authorized
distributor for most of the original component manufacturers (White-Rodgers.
Honeywell, Johnson Controls, Robertshaw, Fenwal, Essex, G.E., Flair, Erie,
Taco, Bell & Gossett, Grundfoss and many, many others). Unfortunately, since we ARE NOT authorized
distributors for most of the finished product manufacturers listed above, we DO
NOT always have easy access to model # to part number cross reference
data. Therefore, for us to provide a
timely response we prefer that customers provide us with all NAMES and NUMBERS
LISTED ON THE ACTUAL PART
Following
are some additional guidelines:
==========================================================================================================================
1]
For all Honeywell controls, they often use the same p/n labels for many
different parts within a series.
Therefore, the part number listed on a plastic label, or the paper label
inside an electrical enclosure cover is incomplete. The complete number is often ink stamped on the underside (or
smallest dimension) side of the component, and includes the last four numeric
characters, i.e. L8184J4009 or S8610H1038.
The first letter (sometimes it's two letters) of the Honeywell part #
indicates its function, i.e. R is relay, L is limit, M is motor (valve or
damper), T is thermostat, V is a valve, AT is a transformer, Y is a packaged
kit, etc. The first numeric character
indicates what type of switching or voltage the control is to perform:
20
series::
3-wire low voltage (2 position). Makes
circuit to start; makes circuit to stop .
eg V2045
40 Series: 2 wire line
voltage (SPST), Makes circuit to start; breaks it to stop. e.g. L4008
50 Series: Mechanical
(non-electrical) series.
60 Series: 3 wire line voltage. 2 position (SPDT) Can
replace 40 series. e.g.:L6008
70 Series: Electronic Series
80 Series: 2 wire low
voltage. (SPST). "S"
preceding series (after first alpha character) indicates millivolt
applications. e.g. TS (thermostat) or
VS (valve). e.g. T87F (TS8 would be millivolt)
90 Series: 3 wire low
voltage, modulating. Varies resistance
between common terminal and two end terminals in response to controlled
variable. Any 90 series with a
"P" following the first alpha character (e.g. TP970) is pneumatic,
and may not contain any electrical components.
e.g. T921, M9164
==========================================================================================================================
2]
For all electric motors, we need to know:
a)
ALL printed data from the motor’s nameplate.
Also include (especially if nameplate data is missing or hard to read)
b)
Direction of shaft rotation - as either
clockwise or counter clockwise when facing the shaft. It is usually easiest to determine rotation when it’s still
installed in the appliance. If it’s a
double shafted motor, indicate CCW or CW when facing the lead (wire) end. CWLE, CCWLE.
c)
Shaft diameter and length(s) to nearest 1/8th inch. Most small HVAC motor shafts will be 1/2 with a flat (48 frame),
or 5/8" with a keyway (56 frame).
d)
]How the motor mounts - either using a “belly band” clamp, via studs parallel to the shaft, or cradle
mounted and secured with round “saddle” clamps
around the bearing housings. If
belly band clamp mounted, please also indicate the diameter of the motor
housing Hey! If the motor can't be properly mounted, no other information is
of any use!
e)
If it is an air conditioner condenser fan motor, please indicate if it mounts
with its shaft horizontal, vertical-UP, or vertical-DOWN.
f)
Voltage, phase and brand of motor when known.
g)
Enclosure. Most indoor motors are
considered open, ventilated. Most
outdoor (condenser fan) motors are usually, at least, enclosed on that portion
of the motor which is facing upward. If
the motor is exposed to rain, it is likely either totally enclosed, or open
only on that end-bell which faces down.
==========================================================================================================================
3] For fan blades: Please, always check for direction of rotation before
disassembling, and verify:
a)
# of blades
b)
Diameter
c)
Direction of rotation (CW or CCW when facing inlet side
providing hub access)
d)
Bore diameter for motor shaft – most often ½” for A/C
condenser fans
e)
Degrees of Pitch (this is hard to determine. In lieu, please indicate width of each
blade, and overall vertical height of blades when resting on a flat surface.
f)
HP and FL AMP rating of motor driving blade
g)
Most fan blades are composed of a steel yoke with aluminum
blades attached with 3 or 4
rivets. Please indicate type of
material (plastic, aluminum, steel)
==========================================================================================================================
4]
Blower Wheels. Again, always check for
direction of rotation before disassembling, and provide the following:
a) Single inlet or double inlet wheel (single
inlet wheels have solid back plate at the end of the wheel) Double inlet wheels will have a centered
hub, whereas air will enter the wheel from both sides.
b) Overall diameter of wheel, measured to the
outside edge.
c)
Width of wheel.
d)
Bore diameter for motor shaft. most often ½” for furnace blowers, except
occasionally 5/8” on some Heil models.
Small wheels (2” to 7” diameter) are usually from ¼” – 3/8” bore.
e)
Composition (aluminum, plastic or steel)
==========================================================================================================================
5]
For all boiler circulator or booster pumps or pump repair parts, please
indicate:
a) In-line or end-suction piping
configuration – Most residential heating pumps are in-line.
b)
Brand name and pump model #
c)
HP & voltage of motor
d)
Nominal pipe size at pump connection (3/4, 1, 1-1/4”MPT,
etc)
e)
2-bolt or 4-bolt flanges (connections from pump housing to
pipes)
f)
Application - if used on heating system only (usually
painted red or green – if Taco) or used to pump potable water in an “open”
system providing domestic hot water (usually painted gold or bronze).
Please
email your request, and we'll promptly reply with current price, availability
and shipping charges. If substitute or
generic replacements are all that is available, we'll indicate such.
We
Accept Visa and MC, Corporate AMEX and advance payments via check. No CODs, please.
Johnstone
Supply of Philadelphia
4700-B
Wissahickon Ave.
Philadelphia,
PA 19144
800-321-4822